天然橡胶/顺丁橡胶/丁苯橡胶自润滑喷蜡橡胶材料的性能

在天然橡胶(NR)/顺丁橡胶(BR)/丁苯橡胶(SBR)为基体的自润滑喷蜡橡胶材料中加入芥酸酰胺,考察芥酸酰胺作为润滑剂时对NR/BR/SBR自润滑喷蜡橡胶材料的硫化特性、力学性能、门尼黏度、摩擦系数及耐老化性能的影响。结果表明,与未加芥酸酰胺的胶料相比,当芥酸酰胺用量为10份时,胶料转矩减小,焦烧时间和正硫化时间缩短,扯断伸长率从388%增加至523%,拉伸强度降低了21.36%,邵尔A硬度、压缩永久变形分别下降5.56%和8.74%,动、静摩擦系数分别减小23.46%和24.82%,门尼黏度降低20.89%,耐热氧老化性能下降。硫化胶拉伸100%停放5 min后,表面出现明显的白色润滑膜,胶料流动性变好,各组分分散得更均匀,断面更光滑。     

2Cr13Mn9Ni4不锈钢卡箍腐蚀开裂分析

2Cr13Mn9Ni4不锈钢卡箍在服役条件下大量出现开裂、断裂问题，为飞行安全埋下较大的隐患。对大量卡箍裂纹进行统计分析，发现其断裂位置、形貌有相似性，进行2Cr13Mn9Ni4不锈钢卡箍腐蚀开裂分析，对卡箍的安全应用有重要意义。对故障件外观进行观察，对断口进行宏微观特征观察、能谱分析，对焊缝附近进行金相组织检查、硬度分布测试，在故障件上取样进行晶间腐蚀试验、热模拟试验，最后对卡箍应力进行模拟仿真。结果表明:卡箍残余应力、环境腐蚀、焊接影响的晶间敏化共同作用导致卡箍开裂。     

Delay Constrained Relay Node Placement in Wireless Sensor Networks: A Subtree-and-Mergence-based Approach

Wireless Sensor Networks (WSNs) are applied in many time-critical applications, e.g., industrial automation and smart grid. This highlights the importance of Delay Constrained Relay Node Placement (DCRNP) problem that builds a path fulfilling a specified delay constraint between each sensor and the sink by using a minimum number of relays. Due to the NP-hardness of the DCRNP problem, in this paper, a polynomial time Subtree-and-Mergence-based Algorithm (SMA) is proposed to approximately solve the DCRNP problem. First, a shortest path tree rooted at the sink and connecting all sensors is built to check the feasibility of the DCRNP problem. If the DCRNP problem is feasible, then the paths of this tree are progressively merged at some relays, which are not limited to those relays lying in the originally the originally built shortest path tree, to save deployed relays while maintaining the obedience of delay constraints. With the repetition of this mergence, the number of deployed relays is gradually reduced. Furthermore, the approximation ratio and the time complexity of the proposed SMA are elaborately analyzed. Finally, extensive simulations are conducted to demonstrate the effectiveness of this work. Simulation results show that SMA can significantly save deployed relays comparing with existing algorithms.     

Unusual Two-Step Assembly of a Minimalistic Dipeptide-Based Functional Hypergelator

Self-assembled peptide hydrogels represent the realization of peptide nanotechnology into biomedical products. There is a continuous quest to identify the simplest building blocks and optimize their critical gelation concentration (CGC). Herein, a minimalistic, de novo dipeptide, Fmoc-Lys(Fmoc)-Asp, as an hydrogelator with the lowest CGC ever reported, almost fourfold lower as compared to that of a large hexadecapeptide previously described, is reported. The dipeptide self-assembles through an unusual and unprecedented two-step process as elucidated by solid-state NMR and molecular dynamics simulation. The hydrogel is cytocompatible and supports 2D/3D cell growth. Conductive composite gels composed of Fmoc-Lys(Fmoc)-Asp and a conductive polymer exhibit excellent DNA binding. Fmoc-Lys(Fmoc)-Asp exhibits the lowest CGC and highest mechanical properties when compared to a library of dipeptide analogues, thus validating the uniqueness of the molecular design which confers useful properties for various potential applications.     

The Modification of Chrome Tanned Leather by Polyethylene Glycol-Linked Gemini Fatty Alcohol Phosphate

A series of polyethylene glycol-linked Gemini fatty alcohol phosphate surfactants (GFAP) were prepared with long chain n-alkanol (C = 8, 12, 16, 18), polyethylene glycol (PEG-200, PEG-400, PEG-600, PEG-800, PEG-1000) and phosphorus oxychloride (POCl₃). The structure of the prepared surfactants was characterized by Fourier transform infrared spectrometer (FT-IR). The surfactants were employed for the modification of chrome-tanned leather. The morphological changes of chrome-tanned leather and modified chrome-tanned leather were observed by scanning electron microscopy (SEM). The relationship between the alkyl chain length and molecular weight of the PEG and the hydrophobicity, softness, mechanical strength of modified chrome-tanned leather was also discussed. The experimental results showed that the mechanical strength and softness of modified chrome-tanned leather were enhanced with an increase of alkyl chain length, while the hydrophobicity, mechanical strength and softness were decreased with an increase of molecular weight of the PEG. The hydrophobicity, mechanical strength and softness of modified chrome-tanned leather were optimized for an alkyl chain length of 16. Therefore, 16–200 Gemini phosphate surfactants with an alkyl chain length of 16 and a PEG molecular weight of 200 have a good comprehensive modification effect on Chrome-tanned leather, the tensile strength, tear strength and softness of modified chrome-tanned leather are 57.07 N mm⁻², 79.49 N mm⁻¹, 9.73 mm, respectively.     

Effect of Temperature and Strain Rate on the Hot Deformation Behaviour of Ferritic Stainless Steel

Metals and Materials International - The flow behaviour and microstructure characteristics of a ferritic stainless steel were investigated using plain strain compression test on a Gleeble 3500...     

Ca(Y, Lu)2Al4SiO12∶Mn4+的制备与发光性质研究

采用高温固相法制备了CaY2-xLuxAl4SiO12:0.006Mn4+ (x=0,0.6,1,1.4,2)荧光粉.研究了Y/Lu组份的变化对荧光粉的晶体结构和发光性能的影响.研究发现,随着Lu组份的增多,荧光粉的吸收峰和发射峰位置都出现蓝移.研究了Mn4+掺杂浓度对CaLu2Al4SiO12∶yMn4+发光性能的影响,发现在掺杂浓度为y=0.004时出现了浓度猝灭现象,浓度猝灭是由Mn4+之间的电偶极电偶极相互作用引起的.研究了不同Mn4+掺杂浓度的CaLu2Al4SiO12∶Mn4+荧光粉的荧光寿命,荧光寿命随着Mn4+掺杂浓度的增大而逐渐降低.     

Effect of clad ratio on interfacial microstructure and properties of cladding billets via direct-chill casting process

Numerical simulation and experiments were introduced to develop AA4045/AA3003 cladding billets with different clad-ratios. The temperature fields, microstructures and mechanical properties near interface were investigated in detail. The results show that cladding billets with different clad-ratios were fabricated successfully. Si and Mn elements diffused across the bonding interface and formed diffusion layer. With the increase of clad-layer thickness, the interfacial region transforms from semisolid–solid state to liquid–solid state and the diffusion layer increased from 10 to 25 μm. The hardness at interface is higher than that of AA3003 side but lower than that of the other side. The bonding strength increased with the clad-layer thickness, attributing to solution strengthening due to elements diffusion. The cladding billets were extruded into clad pipe by indirect extrusion process after homogenization. The clad pipe remained the interfacial characteristics of as-cast cladding billet and the heredity of clad-ratio during deformation was testified.